Products & Services

Wear plates, parts
& reconditioning.

Steel plates carrying a hard, wear-resistant overlay, applied by flux-cored wire welding, fabricated into finished systems, and reconditioned on a turnkey basis.

Weld Overlay Standard Size

Plates & pipes,
off the shelf.

Standard wear-overlay plates and clad pipes in a wide range of base-plus-overlay thicknesses. Dual-side cladding and custom combinations available on request.

Hardfaced Straight Pipes
Hardfaced Straight Pipes
Chevron weld overlay wear plate
Standard Size Wear Plate
Hardfaced Bend Pipes
Hardfaced Bend Pipes

Standard Size Wear Plates

Standard overlay plate stock: width × length in mm, with the available base + overlay thickness combinations.

Width (mm)Length (mm)Thickness: base + overlay (mm)
115049004+2, 5+3, 6+4, 8+4, 8+5, 10+4, 10+5, 10+6, 12+4
140030504+2, 5+3, 6+4, 8+4, 8+5, 10+4, 10+5, 10+6, 12+4
190030504+2, 5+3, 6+4, 8+4, 8+5, 10+4
130029004+8+4 (dual-side clad, any combination)
1300290010+4 to any combination
19006100Min - 3+3mm to Upto 10+6mm Any Combination
14006100Min - 3+3mm to Upto 10+6mm Any Combination

Standard Size ID & OD Cladded Pipes

Standard cladded pipe sizes: overlay-on-base cladding in mm, with inner / outer diameter × length.

Cladding (mm)Inner Ø × LOuter Ø × L
4 on 60.2 m × 1 m0.1 m × 1 m
4 on 6 · 5 on 80.25 m × 1 m0.15 m × 1 m
… · 6 on 60.3 m × 1 m0.2 m × 1 m
… · 5 on 100.35 m × 1 m0.25 m × 1 m
… · 6 on 80.4 m × 1 m0.3 m × 1 m
… · 8 on 100.5 m × 1 m0.4 m × 1 m
… · 8 on 10 (heavy)0.6 m × 1 m0.5 m × 1 m

Composite wear-plate assemblies to 18 on 20 and custom dual-side cladded plates available. Talk to our engineering team.

Fabrication

Manufactured &
reconditioned.

A comprehensive range of industrial wear parts, manufactured new or reclaimed to original specification. Click any image to enlarge.

Full parts range

Wear Plates & Pipes
Standard size wear platesComposite wear plate assembly 18 on 20ID hardfaced bend pipeID hardfaced pipeESP cooler duct
Nozzles, Rings & Chutes
Nozzle ring (Atox mill) & assemblyHardfaced water nozzleGrit cone · Armour ringFeed / discharge / REBD chuteBell housing assembly
Rollers & Rotary
Continuous Casting roller cladding & machiningRoller press roller & machiningRotary air lock (Ø1250 / Ø1800)Rotor seal kit & assemblyClinker crusher rotor reconditioning
Mill, Kiln & Other
VRM tyre reconditioningGuide vanes · Kiln shellPaddle · Scraper plateCNC claddingCustom fabrication

Don’t see the part you need? We manufacture and recondition to your drawing and service condition.

More products / customise →
Super Reconditioning

Reconditioning service at
on-site or off site.

A full-fledged workshop equipped to take up any kind of welding repair or re-building job on a turnkey basis, in the plant or at your site.

Caster roller reconditioning

Reconditioning & Hardfacing

Rebuilding worn rollers, tyres, table liners and rotating equipment to original profile and hardness, extending service life at a fraction of replacement cost.

Custom wear protection overlay

Custom Wear Engineering

Our R&D develops custom-made overlay compositions to meet specific application needs, wear-resistant liner solutions designed around your service condition.

In-Situ Welding

Rebuild the mill,
without pulling it out.

VRM grinding rollers, table liners and roller-press rolls wear down and need re-cladding over time. Our online hardfacing system (and our MOA build-up and surfacing wires) rebuild them in place: no dismantling, minimal downtime.

Grinding-roller drive mounted on the mill
Grinding-roller drive on the mill

Our VRM Hardfacing system mounts an X/Y column-boom rig directly onto the mill and rebuilds worn roller sleeves and grinding-disc linings with flux-cored overlay while the parts stay in place, online or offline. The complete system spans the grinding-roller drive, welding-gun travel mechanism, dust-cleaning device, welding machine, and power-supply & control cabinets, run from a PLC/HMI for continuous, repeatable cladding.

Processes
Open arc · submerged arc · flux & gas-shielded arc welding
Rig & motion
X/Y column boom · 145 mm aluminium beam (custom length) · high-accuracy cross tractor
Wire feed
1.6–3.2 mm flux or solid wire · 4-roller straightener · 2–9 m/min
Power source
1000 A at 100% duty cycle · CC/CV · 24 h continuous
Mill drive
Drive motor, reducer & converter rotate the roller / table during cladding
Cooling & earth
10 L water cooler (~20 m tube) · 360° rotating grounding
Control
PLC/HMI strip / grid / spot cladding · auto air-gouging · handheld remote · usage logging
Products Presentation

The assembled system, annotated.

The complete VRM Hardfacing rig as it ships. Hover or tap the numbered points to identify each part of the assembly.

VRM Hardfacing, assembled column-boom system with numbered parts
01

Y-Axis Beam

Vertical aluminium arm. Stepping lift controls the torch reach.

02

Travelling Cross Tractor

High-accuracy X/Y stepping so the torch reaches every point.

03

X-Axis Beam

145 mm aluminium travel rail: custom lengths, quick-mount.

04

Wire Feeder

4-roller straightener · 1.6–3.2 mm flux or solid wire · 2–9 m/min.

05

Water-Cooled Torch

Runs continuously off the 10 L water-cooling loop.

Plus, off the rig:Water TankPower SourcePLC / HMI
System Components

Inside the system, part by part.

Every part of the VRM Hardfacing rig (from the column boom to the 360° grounding) with its own spec. Hover a part to preview it; click to enlarge.

01X/Y Axis Beam
02Cross-Travelling Tractor
03Wire Feeder
04Wire Feeding Roller
05Welding Power Source
06Mill & Table Drive
07Drive Control Converter
08360° Rotating Grounding
09Gouging Torch (Optional)
10Water Cooler
11PLC / HMI Control
On-Site Deployment

How it sets up on your mill.

The whole system installs around the mill without dismantling it: four steps from mounting to the first cladding pass.

1

Mount the boom

Quick-mount the X/Y column boom at the roller, in the mill (online) or on a 'U'-shape steel fixture (offline).

2

Drive the rotation

Drive motor, reducer and the 380 V control converter turn the roller or table at a steady cladding speed.

3

Ground & power

360° rotating grounding and the 1000 A output cable close the welding circuit while the part turns.

4

Clad from the HMI

The quick-plug PLC touchscreen (or handheld remote) runs strip / grid / spot programs and logs wire and arc time.

Actual Use Case

The final output, in the mill.

2.8 mm open-arc flux-cored overlay laid layer by layer while the roller turns, rebuilt in place, with no dismantling and no transport.

Hardfacing Rebuilding Wires

A two-wire system: rebuild, then armour.

Worn rolls and tables are first restored to profile with an MOA-506 build-up layer, then armoured with an MOA-507 hard surface layer, the same drum-packed wires run through our online rig.

Grinding roll rebuilt with MOA-506 build-up layers
Grinding roll rebuilt with MOA-506 build-up layers
MOA – 506
Build-Up Layer · Flux-Cored Arc Welding Wire
58–61 HRC

Flux-cored build-up wire for the repair and remanufacture of coal grinding rolls and grinding disks, good wear resistance with the toughness to take high-hardness mineral particles.

Wire diameter
2.4 / 2.8 mm
Chemistry (%)
C 4.0–5.5 · Cr 25–30 · Mn 0.4–0.8 · Mo 0.8–1.4 · Si 1.0–1.8 · Fe bal.
Hardness
58–61 HRC
Process
FCAW open arc · 300–550 A · 28–35 V
Interpass temp
Each layer controlled within 100 °C
Packing
Drum packed · 125 / 250 kg

Used for: Vertical crushers, grinding rollers, conveyor armour, wear plates, screen plates, mud pumps & mixers.

VRM table hard surface layer welded with MOA-507
VRM table hard surface layer welded with MOA-507
MOA – 507
Hard Surface Layer · Flux-Cored Arc Welding Wire
62–64 HRC

C-Cr-Nb metal-cored hardfacing wire, niobium- and chromium-carbide alloy with excellent resistance to fine, high-hardness abrasives under severe wear and moderate impact.

Wire diameter
2.8 mm
Chemistry (%)
C 4.0–6.0 · Cr 18–24 · Mn 0.2–1.0 · Nb 6–8 · Si 0.5–1.0 · Fe bal.
Hardness
62–64 HRC
Process
FCAW open arc · 300–550 A · 28–35 V
Interpass temp
Each layer controlled within 100 °C
Packing
Drum packed · 125 / 250 kg

Used for: Roller-press pattern layer and vertical-mill roller / table hard-surface layers.

Applications: cement vertical mills, coal mills, grinding tables, roller-press rolls & continuous-caster rolls, for cement, power, steel and mining plants.

Enquire about online hardfacing →
Consumables

Electrodes &
welding wires.

The flux-cored wires used across our wear-plate range are manufactured by Mailam Upking itself. Backed by our parent’s lab, we also supply joining and anti-wear electrodes, including ghost-spec grades.

Mailam Upking flux-cored welding wires and electrodes
Flux-Cored Wires

Self-manufactured FCAW wire

The formulation of various flux-cored wires is carefully designed to give a weld metal and microstructure that provides extra-long service life under high-stress abrasion, erosion, corrosion, impact and elevated temperatures.

Electrodes

Joining & anti-wear electrodes

For joining composite wear plates, a stainless-steel root run is laid in a double-V groove, then filled with multiple passes of a properly selected anti-wear electrode, a methodology refined over years at MUEL.

Enquire about grades →

Download the product catalogue

Full overlay grade specifications, standard sizes and the complete parts range, in one PDF.

Get the catalogue (PDF) →